- tor 21 nov 2019, 11:46
#1349514
Jag testar alltid det billigaste först = Lyfter minuspolen på batteriet i 30 minuter.
Kostar gratis och du får dina styrenheter omstartade.
Vilken radio har du?
I vissa finns det "hemliga" menyer där du kan kolla i princip allt inkl. antennsignalen.
Advanced User Mode With the radio switched off, press and hold down [Volume] for at least 5 seconds.
! Turn [1-20/DISC] to select a function ! Press [1-20/DISC] to cycle between possible values
Function Description SET TO DEFAULT Resets all AUM (Advanced User Mode) functions to factory settings. AF ON/OFF Automatic Frequency update – Ensures that the strongest available transmitter for a program is selected. REG LOCK/SWITCH Regional – Makes it possible to continue to listen to a regional transmitter, even if the signal is weak. EON LOCAL/DISTANT Enhanced Other Network – Determines whether the radio program you are listening is to be switched off before a traffic report or news broadcast (if these functions are selected) only if the signal is strong (LOCAL) or whether the radio must also try to capture weaker signals (DISTANT). NETWORK ALL/TUNED Network – Allows you to decide whether the radio program you are listening is to be switched off before a traffic report or news broadcast (if these functions are selected) only if the report is on the channel you are listening (TUNED), or whether the program is to be switched off regardless of which radio channel the report or broadcast is on (ALL). ASC ON/OFF Active Sound Control – Automatically matches the sound volume to the speed of the car. ASC Low/Med/High Active Sound Control – Determines the ASC level. SRC ON/OFF SRC = ? – Activates or deactivates the noise reduction in poor reception conditions. Normally used when the radio is in the AM band. SRC Low/Med/High SRC = ? – Determines the SRC level. BACK and SAVE Saves any changes and revert to normal operation. BACK without SAVE Discards any changes and revert to normal operation.
Diagnostic Mode With the radio switched off, press and hold down [AUTO], and press [Volume] to power on the radio. The following will be displayed for 4 seconds:
DIAG WAIT!
Immediately followed by:
Main 23 Sub 25
For some reason, this last display seems to vary from time to time. Other observed values are: Main 29 Sub 22 and Main 29 Sub 24.
! Turn [1-20/DISC] to select a function
Function Description Main-A Exist ? (Display flashes) Sub-A Exist ? Ext-AMP Exist External amplifier detected.
Area Selection With the radio switched off, press and hold down [1-20/DISC], press [Volume] to power on the radio, and continue to hold down [1-20/DISC] for at least 5 seconds.
! Press [1-20/DISC] to cycle between possible values ! Turn [1-20/DISC] to select a function
Function Description AREA EU/US/AU Allows you to select the area where the radio is to be used: Europe (EU), North America (US) and Australia (AU). BACK and SAVE Saves any changes and revert to normal operation.
If no selection is made within 5 seconds, the radio will discard any changes and revert to normal operation.
Hidden Equalizer With the radio switched off, press and hold down [SOURCE], press [Volume] to power on the radio, and continue to hold down [SOURCE] for at least 5 seconds.
! Press [SOURCE] to select a function ! Turn [SOURCE] to adjust value
Function Description FRONT Low1 3 Adjusts the very low frequencies in the front. Valid values are from 0 to 6. Factory default for S60 is 4. FRONT Low2 3 Adjusts the low frequencies in the front. Valid values are from 0 to 6. Factory default for S60 is 4. FRONT Mid 3 Adjusts the mid frequencies in the front. Valid values are from 0 to 6. Factory default for S60 is 6. FRONT High 3 Adjusts the high frequencies in the front. Valid values are from 0 to 6. Factory default for S60 is 4. REAR Low 3 Adjusts the low frequencies in the back. Valid values are from 0 to 6. Factory default for S60 is 4. REAR Mid 3 Adjusts the mid frequencies in the back. Valid values are from 0 to 6. Factory default for S60 is 0. REAR High 3 Adjusts the high frequencies in the back. Valid values are from 0 to 6. Factory default for S60 is 6. Noise Sequence OFF Activates the noise sequencer. A noise sequencer is essentially a noise generator that allows the adjustment of the levels in the system so to achieve the correct balance between the different channels by injecting a noise signal into each of the channels (left, right, centre, surround). Use the sequencer to adjust the balance control until each of the 4 channels individually plays at the same apparent loudness from one of the front seats. Whilst sufficiently accurate balance can usually be achieved by ear, you can use a sound level meter if greater precision is desired. To use this function, the radio must be in Dolby Pro Logic mode. Possible values are: Lch (left channel), Rch (right channel), Cch (center channel), Sch (surround channel) or OFF.
Advanced Diagnostic Menu With the radio switched off, press and hold down [!], press [Volume] to power on the radio, and continue to hold down [!] for at least 5 seconds.
NOTE: The radio source must be “RADIO FM” for this menu to appear.
! Turn [1-20/DISC] to select a function ! Press [1-20/DISC] to enter sub-function or cycle between possible values
Function Sub-Function Description Ver 1316SP72 00 04 Seems to be the version of the EEPROM. DISPLAY CHECK Everything on
Half 1
Half 2
Blank
Accented characters
VOICE CHECK VOICE Lch ON ? VOICE Rch ON ? VOICE OFF ? BEEP CHECK BEEP ON Turns on continuous beep signal. BEEP OFF Turns off beep signal. DTC CHECK Main-A Exist ? (Display flashes) Sub-A Exist ? Ext-AMP Exist External amplifier detected. VOLUME CHECK VOLUME –xxdB Displays the current volume set by turning [VOLUME]. The value of xx varies between –82dB (silence) to –00dB (max volume). Pressing [1-20/DISC] instantly sets the volume to –27dB. CD7 AUDIO ON/OFF ? – I don’t know what this does. When ON, a strange TICK-A-TICK noise can be heard. REASON Int ON/OFF ? STOP ADJUST STOP 26db LV=xx 67 ? – I don’t know what this does. The value of xx varies continuously: DD, DA, DE, etc. AF-C ADJUST AF-C 47dB LV=xx A2 ? – I don’t know what this does. The value of xx varies continuously: DD, DC, DE, etc.
EEPROM INTIALIZE EEPROM WAIT Reinitialises the EEPROM. After a few seconds, the display shows: EEPROM INITIALIZED. EJ+<< ENTRY ON/OFF This is strange. I though it changed the button sequence required to enter the Advanced Diagnostic Menu to ["] + [!] and [VOLUME] but I am not sure of what happened. It might have prevented me from accessing this menu if the radio source is CD.
Fix All 3 Settings With the radio switched off, press and hold down [#], press [Volume] to power on the radio, and continue to hold down [#] for at least 5 seconds.
Function Description FIX ALL3 SETTING ? – I don’t know what are those 3 settings.
The above message is displayed for 3 seconds and then the radio reverts to normal operations.
Extended Settings With the radio switched off, press and hold down [$], press [Volume] to power on the radio, and continue to hold down [$] for at least 5 seconds.
! Turn [1-20/DISC] to select a function ! Press [1-20/DISC] to enter sub-function or cycle between possible values ! Turn [SOURCE] to adjust value
Function Sub-Function Description DIVER TEST ON/OFF Activates the diversity test. When activated, a little 1 or 2 appears to the right of the FM indicator on the display. I am not sure of the purpose of that test but it seems it shows which antenna has the strongest reception as it alternates between 1 and 2 as the car moves. REASON Int ON/OFF ?
CONSTANT Disp >>>> ASC/BAR/DAB/PI/OFF Uses the radio display to constantly display some information on one of the following functions:
ASC (Active Sound Control) M 0km>-57+00=-57 The first value is the ASC level (L=Low, M=Med, H=High), followed by the current speed (in km/h), the volume level (in dB), the correction factor and the adjusted volume (in dB). The correction factors, depending on the ASC level and the speed, are determined as follows:
Speed (km/h) Corr. L M H
+1 72 48 40 +2 104 72 56 +3 136 96 64 +4 ... 120 80 +5 144 88 +6 ... 104 +7 112 +8 128 +9 ...
BAR (?)
- C This seems to be the signal strength of the 2 aerials. The HU-803 is equipped with a “Diversity Aerial System” that allows the radio to automatically select, from one of the two aerials, the strongest signal for the best possible reception (on the FM band). The bar on the left seems to correspond to aerial 2 and the bar on the right to aerial 1.
DAB (Digital Audio Broadcasting) 5A 0 0 0000 00 I haven’t found the purpose of that display.
PI (Program Info???) 107.34A2D C500C3 C The first 5 digits (“107.3” in this case) are the frequency of the selected radio station, the 4 next digits (“4A2D” in this case) seem to be the additional info such as the station name, news availability, etc. Finally, the 6 following digits (“C500C3” in this case) represent the signal strength of aerial 2 (“C5” in hexadecimal notation), “00” (I don’t know) and the signal strength of aerial 1 (“C3” in hexadecimal notation). LEVEL Setting >>>> LVA 12dBu 37H LVB 19dBu 56H LVC 26dBu 67H
LVD 33dBu 6AH LVE 40dBu 86H LVF 47dBu A2H LVG 54dBu A9H LVH SM Drop 4DH LVI AM Drop 2AH LVJ DIV FIX 60H LVK DIV M<->S 10H LVL NOISE 10H LVN DIV SMJUD 50H EXIT
AFS Setting >>>>>> NORMAL Trig 15ms NORMAL Min 1500ms SMETER Trig 20ms SMETER Min 1000ms TUNNEL Min 60s +LV AF 27H +LV REG 47H +TQ AF 10H +TQ REG 47H LOW AF 6T EXIT
DAB Setting >>>>>> LINKAGE ->FM 5S LINK TO FM BER 3H LINKAGE -> DAB 5s LINK TO DAB BAR 4H DAB PTY/TA-R 30s DAB BG(TP) 60s EXIT
OTHER Setting >>>> DIVER Timer 5000ms DIVER S<->M 5ms SRC Detail 0H TC Timer 900ms RC Timer 900ms FM BG(TP) 45s FM BG(SID) 180s PI Defect 600ms NORDS Defect 56ms RDS Judge 40.0ms PLL Lock 0.1ms SM Wait AFS 0ms SM Wait Round 5ms EON Wait 2s EON Prohibit 3s PRE FAST-M 1.2ms POST FAST-M 2.5ms BASS LIMIT Max+1 Varies from Max-6 to Max+6 BASS LIMIT Step2 REASON Time 1000ms DIV LVK UP 20H DIV KUP COUNT 1H DIV KDNTIM 500ms EXIT
NS TABLE Setting > 0-000/1-0BF/2-11F 3-17F/4-1DF/5-23F
6-29F/7-2FF/8-35F
9-3BF/A-41F/B-47F
C-4DF/D-53F/E-59F
EXIT
AF Status >>>>>>>> POOL Status >>>>>> EEPROM >>>>>>>>>>> TP SEARCH ON/OFF RESET Run TEST Exit
XC90 2,5T/AWD/ Automat,
Modellår 2003
28 000mil.
[color =#4000FF]Min Trotjänare.[/color]
- By Solomon
- By Erik Å